How to size your photovoltaic system?
- Author Yoni Levy
- Published October 3, 2010
- Word count 760
How to size your photovoltaic system?
When choosing equipment to meet your power needs, you will need to determine the following, at a minimum:
• The number and type of solar panels required to capture enough solar energy to support your load.
• The minimum capacity of the battery. The battery will need to store enough
energy to provide power at night and through days with little sun, and will
determine your number of days of autonomy.
• The characteristics of all other components (the regulator, wiring, etc.)
needed to support the amount of power generated and stored.
System sizing calculations are important, because unless the system components are balanced, energy (and ultimately, money) is wasted.
For example, if we install more solar panels to produce more energy, the batteries should have enough capacity to store the additional energy produced. If the bank of batteries is too small and the load is not using the energy as it is generated, then energy must be thrown away.
A regulator of a smaller amperage than needed, or one single cable that is too small, can be a cause of failure (or even fire) and render the installation unusable.
Never forget that the ability of the photovoltaic energy to produce and store
electrical energy is limited. Accidentally leaving on a light bulb during the
day can easily drain your reserves before nighttime, at which point no additional power will be available. The availability of "fuel" for photovoltaic systems (i.e. solar radiation) can be difficult to predict. In fact, it is never possible to be absolutely sure that a standalone system is going to be able to
provide the necessary energy at any particular moment.
Solar systems are designed for a certain consumption, and if the user exceeds the planned limits the provision of energy will fail.
The design method that we propose consists of considering the energy requirements, and based on them to calculate a system that works for the
maximum amount of time so it is as reliable as possible.
Of course, if more panels and batteries are installed, more energy will be able to be collected and stored. This increase of reliability will also have an increase in cost.
In some photovoltaic installations (such as the provision of energy for telecommunications equipment on a network backbone) the reliability factor is
more important that the cost. In a client installation, low cost is likely going to
be a the most important factor. Finding a balance between cost and reliability
is not a easy task, but whatever your situation, you should be able to determine what it is expected from your design choices, and at what price.
The method we will use for sizing the system is known as the method of
the worst month.
We simply calculate the dimensions of the standalone system so it will work in the month in which the demand for energy is greatest with respect to the available solar energy. It is the worst month of the year, as this month with have the largest ratio of demanded energy to available energy.
Using this method, reliability is taken into consideration by fixing the maximum number of days that the system can work without receiving solar radiation (that is, when all consumption is made solely at the expense of the energy stored in the battery.) This is known as the maximum number of days of autonomy (N), and can be thought of as the number of consecutive
cloudy days when the panels do not collect any significant amount of energy.
When choosing N, it is necessary to know the climatology of the place, as well
as the economic and social relevance of the installation. Will it be used to illuminate houses, a hospital, a factory, for a radio link, or for some other application?
Remember that as N increases, so does the investment in equipment
and maintenance. It is also important to evaluate all possible logistical costs of equipment replacement. It is not the same to change a discharged battery from an installation in the middle of a city versus one at the top a telecommunication tower that is several hours or days of walking distance.
Fixing the value of N it is not an easy task as there are many factors involved,
and many of them cannot be evaluated easily. Your experience will
play an important role in this part of the system sizing. One commonly used
value for critical telecommunications equipment is N = 5, whereas for low
cost client equipment it is possible to reduce the autonomy to N = 3.
RunGreenPower.com will teach you how to build solar & wind power systems for
your home within a weekend.
Check It Now: [How To Build a Homemade
Solar Panel?](http://www.rungreenpower.com)
Article source: https://articlebiz.comRate article
Article comments
There are no posted comments.
Related articles
- Smart Savings: The Benefits of Buying Out of Season
- How to prepare for a house clearance, a few tips from experts
- Expert and Little Known Tips for Limestone Floor Maintenance
- Top Furniture: Discover the Best of Deutsch Design
- Spring Clean Like a Pro
- Spring into Clean: Transform Your Home with Diamond Home Support Barking
- Spring Cleaning Magic: Unveiling a Fresher Home
- Top Cleaning Tips for the Spring
- The Lemon: Nature's Remarkable Cleaning Marvel
- Why Tree Removal is Essential for Home Safety
- The Dos and Don'ts of DIY Pressure Washing: Expert Tips and Tricks
- Are Silver Travertine Tiles Better Than Other Alternatives? Know How!
- Rustic woodgrain farmhouse cottage with vintage carved barn doors
- Ultimate Guide to Versatile and Secure Storage Cabinets with Locks: A Functional and Practical Solution for Every Space
- The Ultimate Guide to Investing in a Home Lift
- holistic garden sanctuary, buddha statues
- Vintage rustic wood credenzas
- Nature carved Barn Doors
- 7 things you must know before building, extending or renovating your home.
- The Impact of Electrical Upgrades on Home Resale Value in Australia
- Rodent-Proofing Your Home: Tips and Tricks
- How Much Does House Removal Cost in Australia? Understanding Your Moving Budget
- Advantages of Using Ceramic and Porcelain Tiles at Home and Commercial Places
- Culinary Chronicles: A Journey Through Kitchen Renovations
- The Advantages of Using a Professional Cleaner in Liverpool
- Crafting Culinary Sanctuaries: The Poetic Essence of Kitchen Remodeling
- The Importance of Using Professional Tilers for Regrouting Bathroom Tiles
- Making Eco-Conscious Decisions in Home Renovations
- Advantages of Engaging Expert Home Cleaners in Bournemouth
- How To Declutter Your Home - In 5 Simple Steps