ArticleBiz.com :: Free article content
Authors: Maximum article exposure. Publishers: Reprintable article content.  
BROWSE ARTICLES
ArticleBiz.com Home
Featured Articles
Recently Added Articles
Most Viewed Articles
Article Comments
Advanced Article Search
AUTHORS
Submit Article
Check Article Status
Author TOS
PUBLISHERS
RSS Article Feeds
Terms of Service

Cisco CCNA, CCNP, And CCENT Practice Questions: Frame Relay, Inverse ARP, And More!
Home :: Computers & Technology :: Networking
By: Chris Bryant Email Article
Word Count: 436 Digg it | Del.icio.us it | Google it | StumbleUpon it

  

Let’s test your knowledge of Frame Relay DLCIs, Inverse ARP, IPv6 zero compression, and other vital Cisco certification exam topics!

CCENT Certification:

Identify the true statement(s) regarding Frame Relay mapping.

A. Always map the local DLCI to the local IP address.

B. Always map the local DLCI to the remote IP address.

C. Always map the remote DLCI to the local IP address.

D. Always map the remote DLCI to the remote IP address.

E. To allow dynamic mapping, Inverse ARP must be enabled.

F. To allow dynamic mapping, Inverse ARP must be disabled.

Answers: B, E. The frame map statement should reference a local DLCI and a remote IP address. For example, to map the local DLCI 122 to the remote IP address 172.12.123.2, we'd use this command on the Serial interface used to reach that address:

R1(config-if)#frame map ip 172.12.123.2 122 broadcast

Inverse ARP does enable dynamic mapping, but most Frame networks use static routing. It can be a pain to mix static and dynamic mappings, especially when a router is reloaded, so most network admins disable dynamic mapping with this command:

R1(config-if)#no frame-relay inverse-arp

CCNA Exam:

What summary route can be used to advertise the following four routes?

10.4.0.0 /16 10.5.0.0 /16 10.6.0.0 /16 10.7.0.0 /16

Answer: 10.4.0.0 255.252.0.0, or 10.4.0.0 /14 in prefix notation.

CCNP Certification / BSCI Exam:

You are examining an IPv6 address and notice two consecutive colons. What does this represent, if anything?

Answer: Those two colons represent a string of zeros. This is referred to as zero compression, but can only be done once in a single IPv6 address. Leading zero compression, though, can be done as many times as is appropriate in an IPv6 address.

Original format: 1234:1234:0000:0000:0000:0000:3456:3434

Using zero compression: 1234:1234::3456:3434

CCNP Certification / BCMSN Exam:

How many bytes are added to a frame as a result of ISL encapsulation?

Answer: The header is 26 bytes, the trailer containing the CRC value is 4 bytes, for a total of 30 bytes.

CCNP Certification / ISCW Exam:

What command disables ICMP redirects?

Answer: no ip redirects.

CCNP Certification / ONT Exam:

What number and name are given to the highest possible CoS value?

Answer: The highest possible CoS value is 7 (111 in binary), known commonly as Network.

Look for more Cisco and Network+ certification exam training questions on this same website!

Attend a Network+ Boot Camp without leaving home with this special from The Bryant Advantage!

Article Source: http://www.ArticleBiz.com

This article has been viewed 52 times.

Rate Article
Rating: 0 / 5 stars - 0 vote(s).

Article Comments
There are no comments for this article.

Leave A Reply
 Your Name
 Your Email Address [will not be published]
 Your Website [optional]
 What is three + four? [tell us you're human]
Notify me of followup comments via email


Related Articles


Copyright © 2009 by ArticleBiz.com. All rights reserved.

Terms of Service | Privacy Policy | Contact Us | Submit Article | Editorial